Walk-ins welcomeMon–Sat 10am–7pm·Sun 11am–4pm

16 November 2026 · GET Repairs Glasgow

Nintendo Switch 2 Repair Guide: An Engineer's First Look

Our Glasgow workshop examines what the upcoming Nintendo Switch successor means for repairability, common faults, and maintenance.

Across our workbenches here in Glasgow, we have repaired thousands of Nintendo Switch consoles. Between the original 2017 revision, the battery-efficient V2, the Switch Lite, and the OLED model, our micro-soldering irons and hot air stations have seen it all. We have tackled blown power management chips, snapped USB-C pins, worn-out game card slots, and an endless stream of Joy-Con drift.

With Nintendo preparing their next-generation hardware—informally dubbed the Switch 2—we are already assessing what this new console means for long-term reliability and repairability. While official internal schematics remain under wraps, hardware manufacturing trends, supply-chain insights, and years of reverse-engineering current Nintendo hardware allow us to build a clear picture of what will likely end up on our repair benches.

The Expected Faults: What Will Break First?

Consumer electronics generally follow predictable failure patterns, and hybrid handheld consoles face more physical stress than static living-room boxes.

1. Dual USB-C Ports and Power Delivery Failures

Industrial design leaks suggest the new system may feature two USB-C ports (one on top and one on the base) to allow for charging during tabletop play or peripheral connectivity. While convenient for the user, USB-C ports remain one of the most mechanically vulnerable components on any portable device.

On the original Switch, standard wear or using off-spec third-party docks frequently caused the internal port pins to short. This inevitably blew the M92T36 power delivery controller, the BQ24193 battery management chip, or the EN92943 audio IC. If the next console increases charging wattage to support higher-performance silicon, power delivery chips will operate under higher thermal loads. We anticipate USB-C physical damage and charging IC failures will remain our primary micro-soldering jobs.

2. Joy-Con Drift: Hall Effect vs Potentiometers

The original Joy-Cons used mechanical potentiometers with carbon tracks that degraded over time, shedding debris and resulting in phantom inputs. If Nintendo switches to Hall Effect sensors—which use magnetic fields rather than physical friction to measure stick position—stick drift could be largely eliminated. However, if standard mechanical sticks are kept to reduce bill-of-materials costs, stick replacements will remain a routine fix.

3. Thermal Dissipation and Fan Fatigue

A more capable custom processor inevitably draws more power and produces more heat. The original Switch used a small 5 V centrifugal blower paired with a copper heat pipe and thermal paste applied over an aluminium shield plate. For the new generation, thermal management will need to be substantially beefier. Expect denser fin stacks, larger heat pipes, and higher-RPM cooling fans that will be prone to seizing up once domestic dust, pet hair, and lint inevitably make their way through the intake vents.

Hardware Modularity: What We Hope to See

Repairability comes down to modularity. On the original Switch V1 and V2, Nintendo mounted the 3.5 mm headphone jack and game card reader onto a separate daughterboard connected by a ribbon cable. On the Switch Lite, they integrated these directly onto the motherboard, turning a simple five-minute part swap into a micro-soldering job.

For the successor, we want to see:

  • Modular port connections: USB-C ports mounted on secondary sub-boards rather than directly onto the main logic board.
  • Standardised battery adhesive: Pull-tabs instead of the rock-hard industrial adhesive Nintendo historically used to secure their lithium-ion cells.
  • Separated digitiser and display: While modern manufacturing favours fused, laminated displays for visual clarity, fusing the front glass to the display panel drastically raises screen replacement costs for consumers after a minor drop.

What to Do If Your Switch Hardware Fails

If your current console—or its successor—begins acting up, follow these technician-approved diagnostic steps before attempting any drastic DIY fixes:

  1. Do not use metallic tools in the charging port: If the console stops charging, never poke around inside the port with safety pins, tweezers, or paperclips. Bridging the VBUS pin to a data or ground line will immediately fry the charge IC on the motherboard.
  2. Check with a standard low-draw charger: When a console is completely unresponsive, plug it into a standard 5 V/2 A phone charger rather than the high-voltage official dock adapter. Leave it for an hour. If the power management chip is hanging, this lower-voltage trickle can sometimes recover the system.
  3. Inspect the rail connectors: Handheld connectivity drops are often caused by dirty contact pins on the sides of the chassis rather than broken controllers. A quick clean with 99.9% isopropyl alcohol and a soft brush often solves disconnects.
  4. Avoid cheap third-party docks: We cannot overstate this. Unregulated power delivery profiles from cheap third-party travel docks are responsible for a huge percentage of dead handheld consoles that arrive at our workshop.

Realistic Console Repair Pricing

At GET Repairs, we believe in straightforward, transparent pricing across all console hardware. While exact parts pricing for the next-generation Switch will depend on global supply-chain availability, we keep our labour rates fair and accessible.

For context, our charging port replacements on the current Nintendo Switch range from £45 to £55 including parts and labour. Basic component swaps like Joy-Con stick replacements sit around £15 to £20.

We apply this same transparent pricing model to living-room consoles: a standard PS5 HDMI port replacement at GET Repairs is £45 including parts and labour, and an Xbox Series X/S HDMI port replacement is also £45 including parts and labour. If an HDMI port failure has caused a secondary electrical short that damages the on-board retimer or video encoder IC, this is treated as a separate board-level repair and quoted transparently following our free in-store diagnosis.

Expert Console Repairs in Glasgow

Whether you are keeping an original Switch alive or need help with home consoles, you can book a repair at GET Repairs Glasgow. Pop into our workshop with your device, or get in touch through our website for an honest, bench-tested appraisal.

#nintendo#console#repair#glasgow